We spent many hours on research to finding brushless blower cooling fan, reading product features, product specifications for this guide. For those of you who wish to the best brushless blower cooling fan, you should not miss this article. brushless blower cooling fan coming in a variety of types but also different price range. The following is the top 9 brushless blower cooling fan by our suggestions
738 reviews analysed
1. UTUO Brushless Radial Blower Dual Ball Bearing High Speed 12V DC Centrifugal Fan with XH-2.5 Plug 120mm by 120mm by 32mm (4.72×4.72×1.26 inch)
Description
BASICAL INFORMATION
- Dimension: 120x120x32mm
- Screw Hole Spacing: 104.5 mm±0.5
- Weight: 202g
- Connector: XH2.5-2P
- Cable Length: 20cm (8 inches)
- Noise: 61.30 dB-A
AIR FLOW-AIR PRESSURE CHARACTERISTIC
Applicable conditions: Shall be applied in the state when the standard, environmental conditions and voltage are fixed.
- Max. Air Flow: 42.45CFM
- Max. Static Pressure: 41.10mm-H2O
RATED AND OPERATING CONDITLONS
- Rated voltage(VDC): 12V
- Rated current(A): 0.95A
- Rated input power(W): 11.4W
- Rated Speed(RPM/Min): 2800±10％
- Startup voltage(VDC): 7V
- Operating voltage(VDC): 7.0-14.0V
- Operating temperature(℃): -10℃-+70℃
STRUCTURE AND FORM
- Bearing: Dual Ball Bearing
- Structure: Cross flow fan
- Housing: PBT+GF30%
- Blade: PBT+GF15%
ELECTRICAL PROTECTION
- Locked Rotor Protection: Auto Power off after Locked at Rated Voltage for 1 sec. And Then Circuit Attempt to Restart in 2 to 6 Sec.
- Polarity Protection: Open Circuit when Vcc &GND are Exchanged Circuit Won’t be burned within 5 sec. when Vcc &GND are exchanged.
- Insulation Resistance: At least 10MΩ at 500 VDC between Housing and Both Lead Wires.
- Electric Strength: Withstand 500 VAC 1 minute 1mA between Housing and Both Lead Wires
UTUO-USPTO# 86955715 – is a registered trademark protected by US Trademark Law. JUTUONIX products are sold by authorized sellers only.
2. 75mm x 30mm 7530 12V Dual Ball Bearing DC Brushless Cooling Blower Fan AV-F7530MB UL CE
Feature
- Package Content : 1 x DC Brushless Cooling Blower Fan
- Rated Voltage: DC 12V, Current: 0.15A
- Bearing Type: Dual Ball Bearing, Speed: 3000 RPM, Air Flow: 9.40CFM
- Connector: 2 Terminal Connector with 2pin-ph2.5, Lead Wire Length: 250mm/24AWG.
- Life Expectance: 50000 hours at 25 degree, Noise: 28.35dB(A).
- UL CE approved certification. Waranty: 1 year and lifetime support.
Description
Description:
Model: AV-F7530MB
Name: 12V DC BRUSHLESS BLOWER FAN
Rated Voltage : 12V DC
Operation Voltage: DC 6.8-12.8V
Rated Current : 0.15A
Connector: 2pin-ph2.5
Rated Speed: 3000 R.P.M.
Max. Air Flow: 9.40CFM
Life Expectance: 50,000 hours at rated voltage and normal temperature and humidity
Insulation Level: UL Class A
Certificate: CE,UL
Acoustic Noise: 28.35dB***
DC Line Length :240mm
Rotation Direction: Counter-clockwise
Size: 75x75x30mm
Weight: 75g
***:Noise is measured at rated test condition in semi-anechoic chamber in free air with microphone at a distance of 1m apart from the axis of fan at intake side.
*While the fan is running, please do not lock the fan intentionally for a long period of time, the action will lead over-load and over-heat, will damage the fan, even burn the wire.
3. Aibecy 4010 Brushless Blower Cooling Fan Turbo Fan 40 40 10mm 24V DC with Ball Bearing 2Pin Connector for CR-8S Ender 3 3D Printer Hotend Extruder
Description
Features:
DC 24V 0.1A operation voltage, fit for CR-8S Ender 3 3D printer extruder.
2Pin connector, wire length approx. 100cm / 39.4in.
Waterproof , dust-proof and super noise-reduced.
Easy installation and high-efficiency heat dissipation,
Extend the life of your 3D printer, best accessory for you.
Specification:
Volume: 4010
Compatibility: CR-8S/ Ender 3
Noise: 20dBA
Speed: 7600 r/min
Connector: 2Pin
Bearings: Oil-bearing
Cable Length: Approx. 100cm / 39.4in
Rated Power: DC 24V 0.1A
Item Body Size: 4 * 4 * 1cm / 1.6 * 1.6 * 0.4in
Item Weight: 16.5g / 0.6oz
Package Size: 13 * 9 * 1cm / 5.1 * 3.5 * 0.4in
Package Weight: 18.7g / 0.7oz
Package List:
1 * Blower Fan
4. 2pack 50mm x 15mm 5015 12V Dual Ball Bearing DC Brushless Cooling Blower Fan BB5015H12 with 2 Pin Terminal UL TUV
Feature
- Package Content : 2 x DC Brushless Cooling Fan
- Bearing Type: Dual Ball Bearing, Speed: 6000 RPM, Air Flow : 3.87 CFM
- Rated Voltage: DC 12V, Current: 0.23A (0.35 Max.)
- Connector: 2 Terminal Connector with 2pin-ph2.5
- Advantage: Long Life (50000 hours) at 40 degree and Low Noise
- UL TUV approved certification. Warranty: 1 year and lifetime technical support.
Description
Description:
Model: BB5015H12
Name: 12V DC BRUSHLESS FAN
Rated Voltage : 12V DC
Operation Voltage: DC 5-13.2V
Consuming Current : 0.23A(0.35A Max.)
Consuming Power: 2.7W(4.2 Max.)
Connector: 2pin-ph2.5
Rated Speed: 6000 R.P.M.
Max. Air Flow: 3.87CFM
Iife Expectance: 50,000 hours at 40 degree
Insulation Level: UL Class A
Certificate: UL,CE,TUV
Acoustic Noise: 16.0dB***
DC Line Length : 120mm
Rotation Direction: Clounter-clockwise
Size:50x50x15mm
Size:20g
***:Noise is measured at rated test condition in semi-anechoic chamber in free air with microphone at a distance of 1m apart from the axis of fan at intake side.
5. 4PCS 4010 3D Printer DC Brushless Blower Cooling Fan Oil Bearing with 2 Pin Terminal for Hotend Extruder Heatsinks Makerbot MK7 MK8 CPU Chip Arduino Other Small Appliances Series Repair Replacement
Feature
- ❃❃ Made of high quality plastics with high end bearings, this 3D printer part cooling fan can run continuously for days at high speeds without hassle or concern.
- ❃❃ Size: 40*40*10mm / 1.57*1.57*0.39in
- Speed: 6000RPM
- Noise: 27dBA
- DC12 / 24V
- Working Current: 0.06A / 0.08A
- Air Flow: 5.75±10% CFM
- Power: 0.96W
- Cable length: Approx 28cm / 11in.
- ❃❃ Cable connector is already fitted and product is out-of-the-box ready for installation.
- ❃❃ Great replacement item for your all metal hotends or maybe a small cooling fan for your 3D printer nozzle setup.
- ❃❃ Package Including: 4 * 3D Printing Fan. Note: If you meet the fans did not work, you can swap the red and black wires in the plug got it to work. (Any questions, you can contact us and we will give you a satisfied solution!).
Description
This helps to prevent the heat from the nozzle traveling too far upwards.
Without this fan, the filament could get soft above the heater block, which leads to extrusion issues and degradation of print quality.
This is a DC 12V 0.08A cooling fan.
Dimensions are 40mm x 40mm x 10 mm.
Sufficient for use in 3D printing, operating speed is 6000 RPM.
Equipped to properly cool your 3D printer’s extruder assembly, this extruder fan is compatible with the MakerBot Replicator 2 and MakerBot Replicator 2X.
Also compatible with Flashforge, CTC, and other 3D printer types.
Specification:
Rated Voltage: DC 12V
Consuming Current: 0.08A
Connector: 2pin-ph2.5
Speed: 6000 + -10% RPM
Air Flow: 6.5 CFM
Static Pressure: 2.9
Noise Level: 27dBA
Note: Any questions, you can contact us and we will give you a satisfied solution!
Notice!!!
Please check the fan plug, maybe the plug was wired opposite of the fan it was replacing, that is reverse polarity.
6. 4 PCS 3D Printer Blower Cooling Fan, 5015 Cooling Fan 50mm x 50mm x 15mm Fan for Hotend Extruder Heat Sinks with 2 Pin Terminal(12V 0.18A)
Feature
- ✹✹ Power Connection: 2 Pin-ph2.5
- Low noise while cooling the hot end of heatsinks.
- ✹✹ DC 12V 50mm Blower Cooling Fan Hotend Extruder Turbine Fan for cooling heatsinks on hot ends, prints, or other cooling needs.
- ✹✹ Easy to cool the filament that is deposited on your print. Cooling your print can make the difference between a beautiful print and a failed print.
- ✹✹ Size:50mm*50mm*15mm(L*D*H), Speed:6500±10%RPM, Noise:25dBA, Bearing: oil, DC 12V, 0.18A.
- ✹✹ Note: New & Old Version is shipped randomly.(Any questions, you can contact us and we will give you a satisfied solution!).
7. GDSTIME 7530 75mm x 75mm x 30mm 5V USB Blower Brushless Cooling Fan
Feature
- Package include: 1 Piece fan include mounting screws & nuts
- Dimensions: 75mm(L) x 73mm(W) x 30mm(H) / 2.95” x2.87”x1.18”(L*W*H)
- Speed: 2800RPM
- Air flow: 10.5CFM
- Noise: 31dBA
- The wide of inlet is 48mm / 1.9in； The Length of outlet is 36.5mm / 1.44in ±0.3
- The Wide of outlet is 24.7mm / 0.97in ±0.3
- Cable Lenght: 32cm or 12.6 inches
- Weight: 30g or 1.05oz
Description
Package include: 1 Piece fan include mounting screws & nuts
Dimensions: 75x75x30mm
Connector: USB
Rated Voltage: DC 5V
Rated Current: 0.4 Amp
Rated Speed: 2800 RPM
Air flow: 10.5 CFM
Noise: 31dBA
Bearing Type: Sleeve
Life: 35000 hours
Cable Lenght: 32cm or 12.6 inches
Weight: 30g or 1.05oz
8. WINSINN 24V 40mm Fan Blower for Cooling Creality Ender 3 / Pro Turbine Turbo 40x10mm 4010 DC Brushless Hydraulic Bearing, with Air Guide Parts – High Speed (Pack of 4Pcs)
Feature
- ✔️Hydraulic Bearings – High Speed version
- ✔️High quality Hydraulic bearings, Better than Oil bearings, More stable and Long life, suitable for continuous work. The life expectancy is about 45,000 hours.
- ✔️for Cooling Creality Ender 3 / Pro , Rated voltage: DC 24V
- ✔️4010 Blower Fan + 40mm Fan + Air Guide Parts
- ✔️Made by WINSINN.
Description
►Hydraulic Bearings – High Speed version
►High quality Hydraulic bearings, Better than Oil bearings, More stable and Long life, suitable for continuous work. The life expectancy is about 45,000 hours.
►For: Cooling Creality Ender 3 / Pro
►Size: 40x40x10mm
►Rated voltage: DC 24V
►With 2 x Air Guide Parts :))
—————————————————————————————————————
Package include:
►2 x High Speed 4010 24V Hydraulic Bearings Blower Fan
►2 x High Speed 40mm 24V Hydraulic Bearings Fan
►2 x Air Guide Parts
———————————————————————————————————————
Product Warranty:
-WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty.
-If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.
9. WINSINN 40mm Blower Fan 24V 4010 Turbine Turbo 40x10mm for Cooling Creality Ender 3 / Pro Turbine Turbo 40x10mm 4010 DC Brushless Hydraulic Bearing, with Air Guide Parts – Quiet (Pack of 4Pcs)
Feature
- ✔️️Hydraulic Bearings – Quiet version
- ✔️High quality Hydraulic bearings, Better than Oil bearings, More stable and Long life, suitable for continuous work. The life expectancy is about 45,000 hours.
- ✔️for Cooling Creality Ender 3 / Pro , Rated voltage: DC 24V
- ✔️4010 Blower Fan + 40mm Fan + Air Guide Parts
- ✔️Made by WINSINN.
Description
►Hydraulic Bearings – Quiet version
►High quality Hydraulic bearings, Better than Oil bearings, More stable and Long life, suitable for continuous work. The life expectancy is about 45,000 hours.
►For: Cooling Creality Ender 3 / Pro
►Size: 40x40x10mm
►Rated voltage: DC 24V
►With 2 x Air Guide Parts :))
—————————————————————————————————————
Package include:
►2 x Quiet 4010 24V Hydraulic Bearings Blower Fan
►2 x Quiet 40mm 24V Hydraulic Bearings Fan
►2 x Air Guide Parts
———————————————————————————————————————
Product Warranty:
-WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty.
-If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.
Conclusion
By our suggestions above, we hope that you can found Brushless Blower Cooling Fan for you.Please don’t forget to share your experience by comment in this post. Thank you!
